We have all these resources out here in the ether but it’s so hard to pull them into one spot! I was asked, last minute to join a client call today to help convince both the client (affordable housing developer) and the mechanical engineers to "stick with" a commitment to 100% electric design that was publicly stated when the competition was... Read more

As we begin to look into Scope 3 emissions reduction strategies, it's important to understand ways to reduce tranportation emissions to project sites. Is anyone aware of best practices or programs for contractor carpooling to jobsites? I know many of my colleagues travel to work together in one vehicle because of parking limitations, however,... Read more

Welcome to the quiz portion of Toxic Chemicals in Buildings: How to Find and Avoid the Worst Offenders (recorded webcast).

Learning Objectives
Upon completing this course, participants will be able to:


1. Explain how key health hazards and opportunities for healthier choices vary by product category.
2. List... Read more

For Peer Network members and customers with BuildingGreen Premium or LEEDuser Premium membership.

Learn more about our Peer Networks Membership »

Learn more about BuildingGreen Premium Membership »

Learn more about LEEDuser Premium Membership »

"Already a premium or peer network member? Login in... Read more

First, there was Energy Use reductions

Then there was embodied carbon

Soon it will be refrigerant use/leakage calculations

…and much more

As coordinators and leaders of project teams, what does this look like for the practicing architect and our collaborators?

I have no idea. BUT I’m guessing someone is... Read more

Hi all,

We are looking to study Passive House on a couple small multifamily projects. Our understanding is that WUFI Passive only integrates with SketchUp at this time. Our BIM manager has been trying to find an example of a firm that works in Revit and uses WUFI Passive, to point him in the right direction on workflow. I offered to ask... Read more

Ventilation fans, kitchen range hoods, and laboratory fume hoods can use significant amounts of energy from both the fan motor and from venting heated/cooled air out of the building—air that then has to be replaced and conditioned by energy-intensive HVAC systems.

BuildingGreen-Approved Ventilation Fans

BuildingGreen ventilation... Read more

I'm looking to compile an outdoor weather station for a local project, and we'd like to add local outdoor CO2 information to our data. I usually work with Onset HOBO products, but they don't offer an outdoor CO2 sensor. Their weather stations can take data from any CO2 sensor with an analog output - does anyone have any suggestions?

Hi all,

I'm curious if anyone has insight as to the "New Federal Building Performance Standards" that were announced in May of 2021 and then referenced again when E.O. 14057 came out. The memorandum for heads of agencies that was sent out with E.O. 14057 said that the CEQ would issue these standards, but I can't find a commitment to when... Read more

Hello all, 

Wondering if anyone has experience with lead limits in electrical cable and wiring? 

LEED for Healthcare allows a limit of 300 ppm of lead in electrical wire and cabling - my search for compliant products has been all dead ends. (MRc PBT Source Reduction - lead, cadmium, and copper)

Acceptable regulations for... Read more

Hi All, I was initially reluctant to share this, but I've seen similar posts and I think it's in line with our mission and interests so I'll go ahead with it.

Tomorrow 12/9 at 1 PM EST I'm moderating a panel of industry leaders in public health (as it pertains to buildings), construction finance, and project development to review the... Read more

On LEEDuser we divide checklists into multiple project phases. Specifically:

How many of these phases are relevant for BIT best practices?

Note that we also... Read more

Looking for an example or case study for a building utilizing a radiant heating/cooling in climate zone 4a. General use type is office with some public assembly spaces, total of 85,000 sf.

As usual, everyone, especially mechanical engineer, is terrified by the thought of "condensation." So far, I read a DGWW case study, "Energy... Read more

Resilience Resource Database

The Defining and Measuring Resilient Outcomes Working Group has been developing a Resilience Resource Database as a repository for resources related to the topic of resilience in our built environment. 

This database and map are endeavoring to show resources for resilient design across the country to... Read more

Hello Sustainable Construction Leaders,

It's come to our attention that although we shared the slides from last fall's all-network Show & Tell in Atlanta, we neglected to include the presentations from the SCL Summit itself. Since we believe in "better late than never," here they are!

As a reminder: we have permission from... Read more