Shamus Gumshoe

All,

Can anyone suggest a product for the following situation.  We are looking to insulate existing aluminum eterior column covers that have a three inch air gap.  The issue is there is no way to remove the covers without destroying them.  we would like to cut small holes, pump in the insulation  and then cap the holes.  Can anyone... Read more

Hello! We are currently working on an LBC Petal project pursuing the Materials Petal. Does anyone know whether H1 lubricants are inherently Red List Free given they are food grade lubricants? We are trying to figure out whether NSF H1 registered lubricants need ingredient reporting or whether the NSF registration works similar to Delcare, RoHS... Read more

We have a project that is looking for plaster/stucco/textured wall products that are sustainable, or “more sustainable.”

I know these products exist, but I haven’t had to spec or work with any, so I’m reaching out.

The project is in MA, so I'm also soliciting recommendations for products and/or companies who are experienced using... Read more

Our firm held off from signing the AIA Materials Pledge because it was perceived as a feel-good commitment to promise to have good intentions, with no tracking.  I was pleased to learn yesterday that reporting for signatories of the AIA Materials Pledge would "open" today (July 18) and close August 31, and would include mandatory reporting on... Read more

Furnaces heat air that is then distributed through ducting and warm-air registers.

Approved by BuildingGreen

Products approved by BuildingGreen include the highest-efficiency, sealed-combustion furnaces and high-efficiency wood or multi-fuel furnaces. A multi-fuel furnace uses several sources of energy such as wood, wood-pellets,... Read more

Hi Everyone, 

As some of you know, I’ve been working on a new book, People, Planet, Design: A Practical Guide to Realizing Architecture's Potential and I’m happy to announce that it is finally available! 

This book grew out of a decade of thinking about how sustainability fits within architectural practice. It explores the reasons... Read more

A colleague of mine from another firm is seeking a good sustainability consultant in North Carolina. I haven't done work in that part of the country so I'm wondering who you all would recommend.

Thanks,

Carolyn Day

Welcome to the quiz portion of Better Steel, Lower Impacts!

Learning Objectives
Upon completing this course, participants will be able to:


Understand the process of how steel is made.

Recount how the U.S. steel industry has been improving its environmental footprint, while improving product performance.

... Read more

Does anyone have any comparative analysis/reviews of the various energy modeling protocols that includes the 'new' Trane TRACE interface?

Thanks!

Robert Phinney

rphinney@pagethink.com

Hi Fellow Design Professionals: It would be great if you could participate in this important research on the status of professionals addressing extreme heat.

Thanks.

MAL

Planning for Extreme Heat Survey

Our research team from the University of Arizona and Arizona State University is studying how planning... Read more

At the summit we discussed sharing which consultants our firms have used for anti-bias training and EDI education. My office will participate in the upcoming AIA Seattle pilot Intercultural Leadership Program, but that only includes two of our firm leaders. If anyone can refer a consultant in the Seattle region for all-office trainings, I'd... Read more

Hello Green Gurus,

Here is the information for January's Peer Networks Webinar, The AEC Industry is in the Driver's Seat: Strategies to reduce waste & carbon emissions. We hope you will join us!

Register HERE

The AEC Industry is in the Driver's Seat: Strategies to reduce waste & carbon emissions
Thursday,... Read more

Hi everyone,

During the "Integrating Social Sustainability" session at the Winter Summit, an idea was hatched to form a working group dedicated to understanding how equity services can benefit a client's pro forma. Our first step (of course) is to identify the range of services captured under "equity services" and we'd love to speak with... Read more

Hi All,

The SMEPL's Embodied Carbon committee has been hard at work developing a letter that calls for MEP equipment vendors to increase material transparency in their products.  As a way of contacting the most widely-used vendors first, we're asking each of you to enter your "Top 3" specified vendors for each of the products listed in... Read more

It’s Summer Summit season! One of the “good problem to have” challenges we’ve had at recent SDL Summits has been too many great five-minute presentations. It’s hard to find time for them all. This year, since we’ll be online anyway, we can get a jump on that by starting the five-minute presentations early. Plus, we can share them across all the... Read more