This is a bit off the thread of sustainable design leadership, but how much design and/or leadership can you get done without an adequate amount of caffeination?

We are looking for recommendations and advice on improving the sustainability of our breakrooms, particularly on the subject of beverage (mostly coffee, but also a fair amount... Read more

Team,

Many of you saw this from BlackRock.

https://www.blackrock.com/corporate/investor-relations/larry-fink-ceo-letter

SOM, starting with London office, is drafting a letter to our MEP consultants, demanding and holding them accountable for climate change as a preference on consultants selection.

Best,
LL 

Hello all!

I'm new to the group, and so excited to be here. Two part question here (as we think about processes and new year goals).

I am at a smallish firm (20 people) in Boston helping to reform our processes to enable even those that are not steeped in sustainability at a daily level to be comfortable looking for opporutunities... Read more

Hello - 

I am looking for the recording and the PDF/ slides that were shared 3/6 for the project process share-out/ 5 min presentations. It was super inspiring and I would like to refresh my memory of some of what was shared. Thank you!

–
Alison Nash 
AIA, LEED AP ID+C, CPHC, WELL AP
Associate | Sustainability... Read more

Welcome to the quiz portion of Improving Resilience!

IMPORTANT: This quiz covers five related articles within this topic. 

Learning Objectives
Upon completing this course, participants will be able to:


Welcome to the quiz portion of Video: Insights to Success on LEED-CI Certification.

Learning Objectives
Upon completing this course, participants will be able to:


1. Identify key changes to LEED CI 2009 (ID+C).
2. Identify the circumstances of a LEED-CI project that challenge the abilityto certify.
3.... Read more

We have an MEP engineer that is calculating peak loads at about 6 times passive house levels on a large commercial building that is at or near passive house levels of insulation and air infiltration. We suspect one reason is that he is figuring a 50% efficiency level for the ERV. We are showing him ERV systems with 80-90% efficiency, but they... Read more

Hi SD Leaders,

As you may be aware, this past April a group of manufacturers calling themselves the Living Product 50 responded to the letters that many of us sent about five years ago advocating for transparency in their product ingredients.  A copy of that letter can be reviewed about midway through the page at this link:  https://... Read more

Hello all,

This month's SCDL call was full of great discussion! We decided this month that we are feeling good about where we are for the Task Force Agreement on defining social sustainabiltiy in our work. The aim is to work with this agreement for a while and see if it holds up as a process framework. There was also interest to invite... Read more

Hi Everyone, 

Has anyone had success in finding organizations or programs that will recycle the hard hats? We are looking into options for recycling our expired hard hats that can no longer be used. Ideally, we would want to use a company with facilities across the country but we are open to any suggestions or ideas you all may have.... Read more

Following the summer SDL summit - we formed a spinoff user group called "Carbon Sync" to discuss Life Cycle and Carbon Assessment tools like Tally and Athena.  We've had three successful calls with folks sharing a couple 5-minute presentations about various studies and explorations.  We have a mix of experience levels - but are collaborating... Read more

Pipe that delivers domestic water in North America is typically made from copper, chlorinated polyvinyl chloride (CPVC), cross-linked polyethylene (PEX), all of which present environmental challenges. Bimodal polyethylene  (PE-RT) and polypropylene (PP) are potential alternatives with lower climate and health impacts.
... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

Hi Everyone - I hope this isn't a repeat topic. We are starting to get familiar with TallyCAT at SAR+ and have a few people testing our projects in it. Is anyone willing to help us troubleshoot or share lessons learned? We're running into a few errors and wonder if our Revit models and workflow are the issue, or if we need to be doing something... Read more

I'm looking into using solar shingles as a roofing option for a historic building renovation. Has anyone used them before and have any recommendations? I understand they won't be as efficient as traditional panels, but I'd like to figure out if it would be a worthwhile compromise to discuss with the historic commission, if necessary. Thanks... Read more