Hey Team,

I'm in a Living Future session where a number of manufacturers are talking about the low uptake they're seeing in their take back programs. Contractor friends... What barriers (if any) are you running into in using take back programs? How might we as architects help increase utilization of these programs?

Aley

The page you're looking for is no longer available. There may be several reasons:

Welcome to the quiz portion of Changing Building Design Priorities for a Changing Electrical Grid!

Learning Objectives
Upon completing this course, participants will be able to:


Define a “Highly Variable Renewable Energy” generation asset, or VRE, and understand how VREs can most effectively contribute to the... Read more

Hi all,

Just like many of you, our firm is dedicated to increasing representation in the professions and through its relationship to the AIA Large Firm Round Table was able to access a National Organization of Minority Architects Fellow this summer. We’re loving our work with Himesh thus far, but it’s unclear whether we have the workload... Read more

Older buildings—especially those from the 1950s, ’60s, and ’70s—need our help. Many leave something to be desired in terms of aesthetics and comfort. But the truth is that they are part of the urban and suburban fabric now, and they aren’t going anywhere. As tempting as it might seem to tear them all down and replace them with high-performance... Read more

Beginning this year, Miller Hull will not only continue to quantify the upfront embodied carbon of every project we finish through construction, but now purchase third-party certified carbon offsets equivalent to one-third of the project’s impact. Great design is no longer enough - we must take responsibility for our architectural impact in the... Read more

I received the following email from Naajia at Southface.  I'll be out of town until November 8, but I'll see if there's time for me to address at least the second part before I leave:

A question regarding the BIT-User Forum was brought to my attention by a participant. Apparently when you are posting a question and you pick your location... Read more

Hello SD Leaders!

Two weeks ago a group of us gathered for the Winter 2020 Sustainable Design Leaders Summit. Those of us from BuildingGreen that were on site, greatly appreciated everyone's time and energy. It's always a pleasure to work along side you all!

Here is the summit report!

Reminder: We are giving a priority look... Read more

For a number of years a colleague and I have been teaching a course about sustainability and water in architecture at the University of Pennsylvania's architectural school (PennDesign).  This year we're hoping to bring a few new opinions to the table for at the same time as we broaden the discussion.  Because the class will be virtual again... Read more

Five types of green buildings explained. Check out this great infographic by the Pembina Institute: What do net-zero and zero-carbon buildings mean for energy use and climate pollution?

Jake Gehrung
 

* This gets complicated -- how much should happen on the dashboard and how much should happen in the actual Discussion forum?

Hold off on discussions for Phase 1. What should be here instead for... Read more

Composite windows come in two basic types: fiberglass, and wood/plastic composite.

BuildingGreen-Approved Windows

Fiberglass and other composite window lines have NFRC unit U-factors of 0.20 or lower. Higher U-factors are allowed for products that include significant recycled content.

Manufacturers also must demonstrate... Read more

Hello everyone. I am seeking some guidance on crafting an arguement for why my firm should support a change to the Washington State Energy Code which would mandate electric heat pumps for commercial builidngs.  AIA WA is working on the state commercial energy code update under consideration this spring.  We have been invited to sign on to an... Read more

Greetings!

Ayers Saint Gross is in search of a Sustainable Design Coordinator to join our team. This person is anticipated to sit in any one of our offices - Baltimore; Washington, DC; Tempe, Arizona; or Austin, Texas. Fit and skillset are more important than geography. The position is anticipated as full-time, but if the right candidate... Read more

HI All,

I am curious if others are using THERM in-house for your envelope design?

We usually use our building envelope/curtain wall consultants (Boston - so mostly RWDI and Heintjes) but our teams are finding that they need the information faster than our consultants can provide, they are backlogged, or we have some curtain wall... Read more

Welcome to the quiz portion of Certified Wood Update: Comparing SFI to FSC on Key Forestry and Health Issues.

Learning Objectives
Upon completing this course, participants will be able to:


1. Explain the purpose of forest management standards and what they measure.
2. Differentiate between FSC and SFI... Read more