Dear SDL,

After almost 12 years at Sasaki, I have finally decided to leave for a path slightly-less-traveled. My own development project in Boston (passive house, ZNE condos) is in construction and I will be focusing my attention on that over the course of this year, and then hoping to continue doing similar integrated... Read more

We are pursuing sustainability goals (and documentation of those goals) outside of any certification/rating system for a current project.  However, we have set up a criteria list of goals by following strategies/credits from many of those systems (LEED v4 EPDs, SITES v2 threatened tree species, WELL v2 mindful eating, etc.).  This approach is... Read more

Welcome to the quiz portion of Passive House on Campus: Eight Exemplary Projects​!

Learning Objectives
Upon completing this course, participants will be able to:


Explain the primary reasons that higher-education projects are pursuing Passive House certification, including its impact on the environment and occupant health... Read more

Dear SDL'ers

After many months of soul searching about my role as a sustainability leader and how to have the most positive environmental impact, I have decided to take a leave from practice to pursue further studies this September. I will be undertaking a two year Master’s degree at the Institute for Resources, Environment and... Read more

There seems to be a slight glitch in that it was posting Seonhee's picture (love Snoopy!) for the post that Duane sent in - is that correctable?

**Just noticed that you can click on the "Edit" tab on the post and correct (e.g. mis-spelled names (Sorry, Seonhee!).**

We are working on a tenant improvement and want to determine the embodied carbon on bookshelves, product display cases, and desks. Initially finding that Tally is not reading furniture, casework, or fixture families. Are there any tips and tricks you have found to be successful for modeling or defining FFE items in Revit and quantifying... Read more

Hi all,

I'm curious if anyone has insight as to the "New Federal Building Performance Standards" that were announced in May of 2021 and then referenced again when E.O. 14057 came out. The memorandum for heads of agencies that was sent out with E.O. 14057 said that the CEQ would issue these standards, but I can't find a commitment to when... Read more

Welcome to the quiz portion of Shoebox Energy Modeling.

Learning Objectives
Upon completing this course, participants will be able to:


1. Explain the difference between a shoebox model and a whole-building energy simulation.
2. Approach shoebox modeling according to project type and software tool.
3.... Read more

Hi all,

Thanks again to those who presented at the AIA Show & Tell! Here are the slides for some of the fascinating presentations we saw. Please do not share the slides outside of the networks unless they are marked “PUBLIC.”

There may be more to come; if you presented but did not yet provide permission for your slides to be... Read more

Exterior doors often have poor insulation and seals that allow air through.

BuildingGreen-Approved Exterior Doors

BuildingGreen has different criteria for commercial and residential exterior doors.

Commercial swing (hinged) doors must be NFRC-rated, certified, and labeled for U-factor. They have a maximum air leakage of 0.... Read more

Hello all, 

Wondering if anyone has experience with lead limits in electrical cable and wiring? 

LEED for Healthcare allows a limit of 300 ppm of lead in electrical wire and cabling - my search for compliant products has been all dead ends. (MRc PBT Source Reduction - lead, cadmium, and copper)

Acceptable regulations for... Read more

Is LEED Online mind-numbingly slow today for anyone else? Or is it just me? I may give up and try again tomorrow. Frustrating as I was hoping to submit a final review today. :(

Happy Earth Day! I'm sharing the results of our office Earth Day Mind Map, a collaborative event lead by our Green Team with office-wide participation. https://mm.tt/1471242441?t=4c76rJLKXz 

We are celebrating with a virtual happy hour later today and will use the Mind Map to generate conversation and sharing.

I would love to hear... Read more

Folks, it is with a heavy heart that I write this: Lance Hosey passed away unexpectedly on Friday. 

Many of you know him from the early days of the SDL group, or as an outsized presence at any of the many conferences where we overlap. He's been a list-maker, poll-taker and all around troublemaker in my life for over 20 years; I know I am... Read more

We talked about products in Eastern region and Western region groups. 

Guiding questions:

Better Product Choices On Every Project: How To Get There?

How do firms organize and communicate information on materials? Is it office wide or on select projects?

What do designers and project managers need to know? How... Read more

We have a client who is asking us to design a roughly 10 ksf Wellness Center for PHIUS 2021 certification.  The program includes several high density assembly type spaces - roughly 300 person peak occupant load for the building.  The Criteria Calculator that the architect showed us puts the building peak cooling load at 4 BTUH/sf (3000 sf/ton... Read more