Allen Mutapo

Hello,

Are you aware of any bldg codes that have included requirements related to Material Health?

Thanks!

Mona Lemoine Architect AIBC, MRAIC, LEED AP BD+C, LFA, Regenerative Practitioner, RELi AP

Associate, Senior Sustainability Consultant

Mobile: 236-878-1752
mona.lemoine@stantec.com

Stantec... Read more

Hi all,

We recently learned that Mass Dept of Environmental Protection (MassDEP) along with a few other state agencies are looking to offer grants for wastewater heat recovery implemented into projects. This is a newer technology that puts a heat exchanger or heat pump in the wastewater system that then extracts the heat energy and... Read more

Since the launch of the Contractor’s Commitment in late 2020, nineteen companies have become signatories and many others are using the guidelines as a roadmap for their firms.   Now that the pilot year of the Contractor’s Commitment is complete, it is important to consider if and how the guidelines should evolve to be the most impactful.  Over... Read more

Discarded tires are an environmental disaster, and finding a beneficial use for them is a high priority.

BuildingGreen does not approve any flooring product that is made with tire-derived rubber, though some products may be appropriate for exterior use.

I see that the Architect 50 questions this year are organized around AIA 2030 Commitment reporting. I have a question about how people are answering them. The DDX reports have percentages that are by GSF. Are people using this percentage to answer the questions? Or are you calculating the percentage based on number of projects out of total... Read more

We are attempting to use Tally on a couple projects and are wondering how others are using the tool in their design process. If any experienced users out there would be willing to have a brief phone conversation I would appreciate it. Thanks

Pint-flush and non-water urinals can save tens of thousands of gallons of potable water per year. A single non-water-using urinal can save more than 10,000 gallons of water per year compared with the U.S. EPA standard of 1.0 gallon per flush (gpf).

When older 3.0 gpf urinals are replaced, the savings can be as great as 50,000 gallons... Read more

He just posted the following on the Building Performance Knowledge Community forum:

Does anyone have a recommendation for software that is easy to use and relatively inexpensive for doing energy performance analysis at the schematic design (or before) phase?  We are looking for a tool that gives good quantitative comparisons for... Read more

Hi All,

I want to share this report, released today, that I and some other folks on Green Gurus have been working on.  The report dispels the myth that Zero Energy Buildings cost more (specifically in Massachusetts) and it goes further, making the case that Zero Energy Buildings are actually great investments.  Take a look, tell us what... Read more

Hey Gurus. Might anyone have experience, or thoughts, with regard to establishing an energy use baseline for a new advanced manufacturing facility we are working on for a regional technical community college? This type of academic facility is so relatively new, the program doesn't fall into the typical "College/University" building type from ... Read more

Hello Peer Network members,

I have some bittersweet news: I’ve accepted another job and will be leaving BuildingGreen. I’m excited to be the new Community Outreach Manager at Brattleboro VT’s Retreat Farm and to support their mission of connecting people to the land and to each other. I’ve learned so much from being part of this... Read more

Hi All,

If you have 5 minutes, we would appreciate your input in the Google Spreadsheet (linked below).  If you only have 1 minute, feel free to reply to this forum post and list your the typical equipment vendors you spec on projects.  :)

We're asking each of you to enter your "Top 3" specified vendors for each of the products... Read more

Can furniture be hazardous? You bet it can…

From flame retardants in foam cushions to unnecessary stain and dirt repellents on upholstery materials, everyday... Read more

Folks, would love to hear what software you're for in-house daylighting/energy performance modeling at the SD/DD level. My IT folks have been pushing us to try out Autodesk's Insight again after a not so impressive pilot we did a few years ago. Has it gotten better? Was it us? What programs do you feel good about? Which ones really make you mad... Read more