Do any of you have experience with Design For Freedom yet? It came to my attention and I'm trying to investigate. I would love to hear feedback and experiences that you may have at this point. It seems like an opportune moment for this issue of forced labor (yikes! so much I don't know...) to come to the forefront, and I'm curious to hear how... Read more

Depending on seating type­­, these products can contain PVC, toxic flame retardants, hazardous adhesives and finishes, and other unsustainable materials.

BuildingGreen-Approved Seating

BuildingGreen’s seating meets ONE of the following sets of criteria:

Five types of green buildings explained. Check out this great infographic by the Pembina Institute: What do net-zero and zero-carbon buildings mean for energy use and climate pollution?

Hi folks,

Here's the next Peer Networks private webinar. As usual, it will be recorded and shared in the network if you can't make it in person:

Thursday, July 18, 2pm EDT (11am PDT)

The Center for Active Design (CfAD), operator of the Fitwel Certification System, recently launched Fitwel v2.1, which advances a vision where... Read more

Like everyone we’re struggling with the tight labor market. We’re not looking to poach. What we have found previously are individuals that have a passion for high-performance buildings but aren’t working on them in their current role for one reason or another.

Openings include:

Project Manager              3-5 years’ experience on... Read more

Greetings AEC Sustainability Leaders -

This is an update on where we stand with the BBB letter. In addition to posting this to the AEC SDL (Green Gurus) Forum, we are sending the same message to all current signatories by email to make sure everyone is notified. Apologies for putting two items in your inboxes!

First, please read... Read more

Welcome to the quiz portion of The Great Eight: High-Impact Material Choices for Green Building.

Learning Objectives
Upon completing this course, participants will be able to:


1. Specify green building materials in product categories that truly make a difference for human health, the environment, or both.
2. Conduct a... Read more

SAVE THE DATE: ALL Peer Networks Show & Tell
Tuesday, November 19 | 8pm - 10pm
The Kendeda Building, Georgia Tech | Atlanta, GA

Start your time at Greenbuild on a high note!

Join your Peer Networks Colleagues from SDL, SCL, MEP, SDLS, and SAL for a high energy evening full of lightning round previews of the best... Read more

* This gets complicated -- how much should happen on the dashboard and how much should happen in the actual Discussion forum?

Hold off on discussions for Phase 1. What should be here instead for... Read more

This is sort of dragging up an ancient topic, but curious how your firms are currently addressing accreditation (LEED AP, WELL AP, LFA, etc.). There was a time when we were all talking about this, and a number of firms instituted requirements, but it has been a long time, and I'm curious how it's looking now in 2024. Thanks! 

Since starting at LPA last fall, the number one question I get from people outside the firm is how we are hitting (2018-2019) or getting so close to hitting the 2030 Commitment goals. 

Here is a chance to see for yourself! LPA is seeking a Sustainable Design Specialist to join our RED team (Research Education Design) - location open to... Read more

Hello friends. On a current school project, an abuse resistant wall covering has been proposed as an alternative to our typical MDF wainscot. The proposed product has been used successfully in healthcare, and switching to it will save the project almost $1million, which is no small amount when the project is over budget and 7-figure cost... Read more

Quiz body not needed for this auto-confirmation

I am excited to share with you the final draft of the letter back to LP50 manufacturers.  The LP50 manufacturers sent their “Closing the Loop on Product Transparency” to design firms earlier this year.  For more background information, please check out Chris Hellstern's original August 20th post on this Green Gurus forum.  When we posted the... Read more

If your HVAC designers are addicted to the crack that is Trace 700, and knowing that Trane is giving up on that product in the coming year, what loads program are you weaning* them onto?

Asking for a friend:  Have any of you had success in using the Revit plug-in for loads?

*When told that they should use IESVE for loads, our HVAC... Read more