All,

I'm sure a few of you attended our recent  webinar on the LEED v4.1 LCA webinar. In case you missed it, the recording is posted. We were stunned by the amount of engagement from the audience; we allotted 30 minutes for questions and I think it went even longer. The webinar recording should be a great starting point for anyone... Read more

Hi Friends, 

I'm working on an SOP for construction waste management for LBC core and LBC materials petal projects and wanted to get your input on the comingled facility requirements. According to the guidelines, any waste that goes to a comingled facility must be a facility that has an average diversion rate of 80% or higher as a... Read more

Currently, the BIT User site is fully accessible without having to log in (unless you want to edit or add content, of course). The time has come, however, to start restricting access only to logged-in users.

Which sections will be freely visible, and which will be visible only to registered users? Here's what I recall from our earlier... Read more

Ada Fran Maman

Hey Gurus. Might anyone have experience, or thoughts, with regard to establishing an energy use baseline for a new advanced manufacturing facility we are working on for a regional technical community college? This type of academic facility is so relatively new, the program doesn't fall into the typical "College/University" building type from ... Read more

Hi Sustainability Leaders,

(Note: this post was edited to correct Jen's affiliation and to add Rob Winstead.) Please join me and the BuildingGreen team in congratulating the Peer Network members of the USGBC 2023 Class of LEED Fellows!

Geoffrey Brock, IPS-Integrated Project Services, SCL

Heather DeGrella, Opsis... Read more

We are cautiously rekindling the age-old debate: how are we balancing modeling software for design /visualization and performance analysis during early phase of design.  

We are heavy SketchUp users for early design, and most of our staff have access to COVE tool for early performance analysis. Problem is, I’d rather use Revit to COVE... Read more

Hello Green Gurus,

Here’s a reminder that our first Show & Tell for 2021 is happening next week! Monday, February 1st from 7-8pm ET and Tuesday, February 2nd from 4-5pm ET, come see your peers from all networks present for five minutes each on a variety of topics relating to their work.

This event is connected with the Summit-... Read more

The current Stantec/BuildingGreen featured topic is Material Health. Read on to learn the essentials, and then dive deep to earn CEUS.

Also see the Resilient Design featured topic, and also a survey of topics trending in Stantec’s regions.... Read more

Was anyone else surprised to see ASHRAE 228-2023 using eGRID Subregions for both the Regional Electricity Source Energy Conversion Factor and Regional Electricity Greenhouse Gas Emission Factors? In the past I have used eGRID sub-regions but also State and local utility conversion factors depending on what energy or operational carbon story I... Read more

Hi All - I wanted to share out the All For Reuse initiative below by two peers in the sustainable materials management network. I know some SDL have already done much research on this from quite a few angles, and those with LBC experience probably even moreso in practice. 

Frances Yang (Arup) and Andrew Ellsworth (Doors Unhinged) have... Read more

Five types of green buildings explained. Check out this great infographic by the Pembina Institute: What do net-zero and zero-carbon buildings mean for energy use and climate pollution?

Dear all,

A mechanical engineer on a healthcare project we are working on has asked for help in dividing the ventilation calculations between ASHRAE Standards 170 and 62.1; can anyone here help shed some light on it?

"This is the first time I am working on LEED for a hospital and I am not sure how the template wants me to show... Read more

Hi folks,

Mahesh announced today that he's leaving his position as CEO of USGBC, GBCI, and ArkScoru, effective Nov. 1. An interim CEO will be announced tomorrow.

I think that Mahesh did some great things for the organization(s)--and he had some really loyal team members. He could also be challenging to work with--as I learned... Read more

Hi Everyone!

Here is your friendly reminder for the last call to submit your Salary Survey! Here is a PDF to collect your thoughts first if that is helpful.

*This survey will be closed end of day Friday Feb. 15th.*

Important Note: There is a link to a Google Form at the end of the survey to let us know you have completed... Read more