Furnaces heat air that is then distributed through ducting and warm-air registers.

Approved by BuildingGreen

Products approved by BuildingGreen include the highest-efficiency, sealed-combustion furnaces and high-efficiency wood or multi-fuel furnaces. A multi-fuel furnace uses several sources of energy such as wood, wood-pellets,... Read more

Hello all,

I am reaching out to this community as SMMA has a job opening for a Sustainable Design Analyst (like many of you recently posting job openings on this forum).

Here is the job posting link: https://smma.applytojob.com/apply/mah0aDkOJ0/Sustainable-Design-Analyst

Please note that this position will support... Read more

I've been hearing recommendations for bipolar ionization, as a way to filter airborne virus particles in HVAC systems while avoiding the energy penalty of increased ventilation. However, I've also heard that ionizing equipment is dangerous because it produces ozone.

Does anyone have any insight into the effectiveness and/or cautions... Read more

All,

Our firm has been struggling to find carbon reduction strategies for concrete that move us beyond a fly ash only approach. Frankly, the knowledge just isn't there internally or with our consultants. We've known that there are a few folks out there that have a deep bag of tricks, but we haven't had the chance to work with them... Read more

Hello Sustainable Community Design Leaders!

Let’s take a moment, introduce ourselves, and get to know each other and our work! Don’t forget to fill out your BG.com profile with your headshot and bio; this is how everyone across Green Gurus can see you in the Member Directory. 

I’ll kick us off! I'm RoseAnn, I also go by Rose, Peer... Read more

Well done and rivhly deserved, brother.  That makes you a Fellow Squared.

A couple questions for this group. I know we're having a Green Commons meeting on this next week. But can anyone comment on the following questions?

-Have you or your firm split the benefit of the 179D with a client? Is this typical?

-Is prevailing wage a requirement for all 179D benefit, or does it follow the same lines as... Read more

Show & Tell Break-out Session: Post Occupancy Evaluations and Occupant Behavior

Presentations: 

All,

Beck is making great strides in our AIA 2030 Commitment and we are looking for an experienced energy modeler to join our team, please reach out if you know of anyone that is looking and has energy modeling experience.  the job is posted on our website:  https://beckgroup.applicantpro.com/jobs/1011136.html

Hi Friends, 

I'm working on an SOP for construction waste management for LBC core and LBC materials petal projects and wanted to get your input on the comingled facility requirements. According to the guidelines, any waste that goes to a comingled facility must be a facility that has an average diversion rate of 80% or higher as a... Read more

Welcome to the quiz portion of BuildingGreen’s Top 10 Green Building Products for 2018.

Learning Objectives
Upon completing this course, participants will be able to:


1.  Explain the transparency and optimization criteria in the LEED v4 (applicable to  Building Product Disclosure and Optimization credits in LEED v4 BD+C and... Read more

Was anyone else surprised to see ASHRAE 228-2023 using eGRID Subregions for both the Regional Electricity Source Energy Conversion Factor and Regional Electricity Greenhouse Gas Emission Factors? In the past I have used eGRID sub-regions but also State and local utility conversion factors depending on what energy or operational carbon story I... Read more

Welcome to the quiz portion of Avoiding the Global Warming Impact of Insulation.

Learning Objectives
Upon completing this course, participants will be able to:


1. Define “embodied global warming potential” and “lifetime global warming potential” as they relate to insulation materials.
2. Describe why some... Read more

We are cautiously rekindling the age-old debate: how are we balancing modeling software for design /visualization and performance analysis during early phase of design.  

We are heavy SketchUp users for early design, and most of our staff have access to COVE tool for early performance analysis. Problem is, I’d rather use Revit to COVE... Read more