All,

I'm looking for a quick methodology to estimate GHG emissions from refrigerants on a per SF basis. Are there any benchmark studies or quick calculators similar to the embodied carbon study? https://carbonleadershipforum.org/embodied-carbon-benchmark-study-1/

Thanks,

Josh

Has anyone worked on a project installing a PowerNest system?  I just found out about it today and would love to get working information on it.  

Here's the link, in case its new to you as well. https://www.ibispower.eu/home

Thank you -

Hello all,

Does anyone know of any Rebate Program for either induction cooking equipment or kitchen electrification (new or existing)? Looking for any local or state or even federal programs (outside of California) that incentivize designing/building/retrofitting towards an all electric kitchen for any program type (institutional, single... Read more

Welcome to the quiz portion of LEED vs. Green Globes: A Definitive Analysis

Note: If you are taking this quiz as a member of LEEDuser, please take the quiz here.

Learning Objectives
Upon completing this course, participants will be able to:


1. Highlight the most significant differences between LEED and Green... Read more

As part of the Philadelphia AIA COTE, we have been proposing implementing sustainability in some fashion into the design awards with our chapter's design committee.  I know that many of you have been down this road before, and wanted to get your feedback at a high level about what your local COTE is doing.  Anyone who's interested, can you... Read more

I've been seeing Armstrong's DC flexzone ceiling system at Greenbuild for many years. I'm working on a net zero project with LED lights and solar panels. In theory, the transmission losses in going from DC power from panels to AC for the building to DC for the lights would be eliminated. But does anyone actually have experience using this... Read more

Hi Green Gurus, 

I am happy to join this group, and would like to share a short introduction of myself. I’m Jais, and I am with FXCollaborative as a Sustainability Design Specialist working with Ilana Judah. I have been here little over a month and am enjoying it so much! 

I have studied architectural design focused on... Read more

I’m a volunteer member of the ASHRAE 209 ("Energy Simulation Aided Design for Buildings Except Low-Rise Residential Buildings”) Committee.  Are you familiar with ASHRAE 209? It was first published in 2018, and it outlines a process for incorporating energy modeling into the design process. 

From the forward: 

 ASHRAE Standard 209... Read more

All,

My team at WSP has a pretty awesome senior position available and I wanted to bring it the group's attention as we try to get the word out. The role is to lead our Sustainable Design Analytics group (part of our Built Ecology team), ideally based in CA or NYC, but open to wherever good candidates may be. If anyone knows someone that... Read more

Hi everyone,

Thanks so much to those who attended and shared at the Greenbuild 2024 Show & Tell! As always, we had a riveting lineup of presentations.

The slides for the presentations are below. We have permission from all of the following presenters to share the slides within Peer Networks-only spaces, but only the slides... Read more

Faucets with high flow rates waste water—not to mention the energy used to treat and deliver it to our buildings—and the additional water stresses our wastewater treatment systems.

Hi folks,

For those in the SD Leaders network, here's a reminder about the webinar this Friday at 2:00 eastern time. I hope you can join us!

For other Green Gurus, you're welcome to join in, get a preview of the report, and learn about what happened at the SDL Summit at Gulf State Park, in Alabama (fortunately, NOT near where the... Read more

Hi folks,

We had a rich conversation in our monthly meeting last week. I've summarized the highlights below. Next call is July 11 at 2pm eastern. If it isn't already in your calendar, here's the Zoom link.

What’s on people’s minds?

Looking into high-temp water-source heat pumps for industrial applications. Transom and... Read more

Green gurus!

We're getting some interest from clients abroad on two specific materials which we don't have experience with here in the U.S.:

1) Cross Laminated Timber (CLT)

and/or 

2) CarbonCure concrete

Anyone willing to share lessons learned on these material either here in the forum or offline? Or point me... Read more