Hello Green Gurus,

Here is the information for our second Peer Networks Webinar this month, coming up next week: Better Products = Better Buildings (Low Carbon Specs). We hope you can join us!

Register HERE.

Better Products = Better Buildings (Low Carbon Specs)
Thursday, May 19, 2022
1 - 2pm ET (10 - 11am PT)... Read more

Hi: Great to see so many of you at AIA COTE Top Ten last week.  I'm forwarding the message below for those of you who know Marsha Maytum and can contribute to this important effort. Deadline is next Friday June 23rd!Thanks.

Mary Ann

Hello, friends,

During A'23, Je’Nen and I discussed our desire to send Marsha photos we have... Read more

Has anyone documented the Food Alternatives credit as part of WELL or as an innovation credit in LEED?

Here is a fundamental question regarding measuring operational carbon emissions that I'm sure many of you can clarify for me:  Let's say you are considering design options and you want to know the relative contribution of GWP of adding an additional inch of continuous insulation to the building envelope.  The GWP from embodied carbon will... Read more

Hello Everyone,

Here is the information and invitation to complete the SCL Demographics Survey! If you have multiple company colleagues on this forum (you can check in the group list here click "Group members" tab), please coordinate to have only one of you submit survey responses.

If you would you like to gather your answers... Read more

Has anyone used a commercial heat pump water heater for a large protect?  I have found a few manufacturers for this technology, but want to make sure this is a viable and cost approach to electrical eliminate gas on a path to all electric.

Hi everyone - in doing a carbon footprint for our firm, does anyone know if buildings that we design as Architects considered scope 3 emissions, or are they beyond the boundary of emissions? LMN's buildings, despite best efforts, are cumulatively multiple orders of magnitude above our scope 1 and 2 emissions. We have never included these... Read more

Producing a ton of cement releases approximately a ton of CO2 into the atmosphere, but accessories like finishes and additives can also be major sources of VOCs, soil contamination, and human health risks.

BuildingGreen-Approved Concrete Accessories

BuildingGreen approves the following concrete accessories:

On behalf of the LFRT IRA working group, I am writing to see if anyone has applied for IRA funding (48E, 45L, 179D) for their project, and is willing to share their experiences and basic project info with us.  We can keep the project name confidential if needed.

Thank you!

Hi all,

I'm curious if anyone has insight as to the "New Federal Building Performance Standards" that were announced in May of 2021 and then referenced again when E.O. 14057 came out. The memorandum for heads of agencies that was sent out with E.O. 14057 said that the CEQ would issue these standards, but I can't find a commitment to when... Read more

Welcome to the quiz portion of How To Run a Great Workshop: 37 Tips and Ideas.

Learning Objectives
Upon completing this course, participants will be able to:


1. Explain how the right mindset contributes to a successful design workshop.
2. Schedule a design workshop, set its agenda, and balance the skills of its... Read more

Hello all, 

Wondering if anyone has experience with lead limits in electrical cable and wiring? 

LEED for Healthcare allows a limit of 300 ppm of lead in electrical wire and cabling - my search for compliant products has been all dead ends. (MRc PBT Source Reduction - lead, cadmium, and copper)

Acceptable regulations for... Read more

Under a high carbon scenario, most of North America will be 2 degrees C hotter by 2050. Meantime, we're designing buildings that will still be around in 2050, to codes that don't yet factor in chronic risks associated with climate change. I want to explain these risks to my colleagues; I'm hoping some of our green gurus can help answer the... Read more

Hello fellow sustainable design leaders! I am about to kick off an intensive effort here at EHDD to refine our internal standards for materials. We will be considering both GWP as well as the health of materials (avoiding harmful chemicals). In addition to setting the standards, I will be working to develop a process to vet materials before... Read more

We have a client who is asking us to design a roughly 10 ksf Wellness Center for PHIUS 2021 certification.  The program includes several high density assembly type spaces - roughly 300 person peak occupant load for the building.  The Criteria Calculator that the architect showed us puts the building peak cooling load at 4 BTUH/sf (3000 sf/ton... Read more