At the recent All Networks Workshop in Seattle, I listened with interest to some conversation about including sustainability goals, KPI's, critical materials lists, and other related topics on a G-sheet in the drawing set.  This is something I had not previously considered, but would like to learn more about. 

If you work for a design... Read more

"The man with one watch knows what time it is; the man with two is never sure."   --Segal's Law

We recently purchased two indoor air quality meters in the $200-$300 range and find that they never agree, not even close. I would like to find out what other people's experiences have been, and if they have tested affordable models that... Read more

Hi:

I encourage you to review and sign this letter. 

Notes from BDC follow:

Really appreciate the outpouring of support we've received so far on this letter! Various groups let us know that they would like additional time to review, so we've decided to extend the deadline from June 23 to Thursday, July 14 at 2pm.

As... Read more

Hello Sustainable Design Leaders!

Here are the details for an upcoming SDL Peer Network web call, this webinar will be a call to share research and resources around mass timber. Hope to see you there!
REGISTER HERE!

Embodied Carbon and Mass Timber – a shared learning conversation
March 31st, 2020
3pm - 4pm ET (... Read more

Welcome to the quiz portion of Resilient Design: 7 Lessons from Early Adopters

Learning Objectives
Upon completing this course, participants will be able to:


1. Recount the ten resilient design principles.
2. Recount each of the seven fundamental messages embraced by the model practitioners.
3. Describe... Read more

Protection against corrosion is the primary function of steel coatings, which often contain corrosion inhibitors, volatile solvents, heavy metals, and other hazardous chemicals.

These coatings are specified when steel is used structurally, outdoors, or in high-use areas. In these situations, hazardous coatings are often applied off-site... Read more

Hello Folks,
What is your experience with successes and failures in the design process? As a starting point I have listed my Top 5 for success, and my Top 5 for failure. We'd love to see your reactions and look forward to the discussion when we all meet next week at our monthly check-in.

Top 5 reasons for when integrative design... Read more

Hi all,

We are taking a deep look at green accreditations within our firm. Gone are the days when we could say: "our staff is XX% LEED APs!" as a metric of firm progress. Here are a few questions we are asking ourselves, and I'm wondering how you approach this in your firms:

Hi All,

Has anyone dug into ASHRAE 2016 as part of the new v4.1 requirements or as codes start to adopt it? I recently presented on this and thought I should check my math to make sure I'm understanding and communicating this correctly.

My understanding is that there is a new reference baseline, that is essentially the ASHRAE 2004... Read more

Welcome to the quiz portion of Saying Goodbye to the Office—and Hello to Housing!

Learning Objectives
Upon completing this course, participants will be able to:


Hello all, excuse the blast and the short timeline -- while not explicity sustainability-related, this is a great way to connect with the future of the profession, and can be a great opportunity for SDL firms on the west coast (a number of SDL firms already participate), specifically in Tacoma, Olympia, San Francisco, Sacramento, or San Diego.... Read more

This article just came up in my news feed. I thought you’d all like to read it. I will point out that C&D-specific MRFs have told me that they are really good at single-stream C & D waste, as long as the drywall is pulled out.  Any drywall in a single-stream C & D dumpster ends up in the landfill. Drywall just breaks apart and gets... Read more

Hello all,

This month's SCDL call was full of great discussion! We decided this month that we are feeling good about where we are for the Task Force Agreement on defining social sustainabiltiy in our work. The aim is to work with this agreement for a while and see if it holds up as a process framework. There was also interest to invite... Read more

Friends of EPIC –

Hey, everyone. As some of you might have heard, we’ve been working for a while with Autodesk to get c.scale (the data model behind EPIC) built into Forma – Autodesk’s AI-powered planning tool. Forma is packaged within Autodesk’s AEC collection and most firms using Revit should already have access. This integration is... Read more

The Sages network is specifically for industry veterans and long-time Peer Network members, including those who are still active with one of the other networks and those who have moved on from that role. This group can help set priorities, drive advocacy, and... Read more

Hey SDL,

I'm curious if anybody out there has developed specification language requiring a certain level of airtightness (as assessed via one or a series of blower door tests) for a commercial project when it is not going for a Passive House certification and a blower door test is not required by code--basically, something in the... Read more

Hi all!

I've heard several people talk about developing tools for assessing/codifying a client's values for a project as part of an integrated design process (ie. a set of questions, survey, etc.). Would anyone be willing to share?

(Z, are you listening? I specifically recall you mentioning a tool like this...)

Thanks!... Read more