Hi Shane and Dennis,

What return address should we use for BIT User forum notification emails?  Ben suggests something like no-reply@bit-user.org but whatever you like is fine.

Once you decide, please let us know who controls the domain name (e.g. bit-user.org or bitbuilding.org).  Ben will send them instructions for editing the... Read more

Greg Calnago

Has anyone here found an alternative to XPS for the void former?

A structural engineering contact was included in recent conversations about embodied carbon in insulation materials and brought to our attention that this is a common use for XPS that has nothing to do with its insulating properties. It is typically used where concrete is... Read more

Ali Flynn and Alejandra Arce Gomez are planning a breakout meeting for the Waste Managment Group for all interested. 

Please fill out the doodle poll below so that we can find a good time:

https://doodle.com/poll/qxd4zxrw9xzrxwc6

Ali and Alejandra have drafted an updated version of the Commitment for Waste (attached) after... Read more

The Sustainable Design Leaders peer group brings together the most committed sustainable design directors from leading architecture firms throughout the U.S. and Canada. We invite you to apply for membership.
We look for the... Read more

I'd love to hear thoughts from the design, consulting, and contracting firms in this group about ways to make our specs more inclusive, or at least less exclusive to minority and women owned contractors and subcontractors and others that have not had the benefit of what a recent "Equity in Specs" presenter termed the "Fathers / Brothers / In-... Read more

Hi Sages,

As you may have seen in my message, the Peer Networks Member List is not very helpful to us (yet), because a person can only show up in one network. Many of us are also in SDL or other networks; there are many more of us than show up when you filter that list for "Sages."

Until we can get that fixed, we'll share the... Read more

Hey All!

One of the initiatives from our first meeting in Chicago was to gather and develop resources related to plug and process loads in buildings which will help us all with: energy modeling, equipment sizing and power distribution.  We had our first call this morning and are rolling.  Aspirations are that this could turn into a... Read more

Hi everyone,

Since I know we have a lot of talented people in this group, I'd like to reach out to those of you based in Los Angeles and see if anyone is interested in talking at an upcoming Living Building Challenge collaborative event.  The topic of the meeting is "Selecting Healthy Materials 101: From the perspectives of... Read more

Hi Green Gurus,

In this stressful time, I think it is important for us to continue to feel connected and supported.  Also, it is difficult to come to terms with the reality of what is happening.  So, I thought it would be helpful for us to share some information about the response of our respective firms to the Coronavirus.

The... Read more

CEUs are available for reading all the building-envelope product guides and primer. Click here to learn more and take the quiz.

Water and air that penetrate building assemblies can damage materials, cause energy loss, and lead to mold, mildew, or other problems. The products used to address these may contain materials that are... Read more

Is anyone aware of research or guidance that has looked at VOC’s from roofing products and ventilation intakes? I’ve done some searching, and focus is mainly on managing the construction process to reduce installer exposure. 

Thanks for any help!

Tate

We're looking to expand our design performance group - let Peter or me know if you have someone to recommend to us! Here's the description. 

Has anyone had any success with achieving the LEED Building Envelope commissioning points with an alternative compliance path using the requirements of the PHIUS verifier? It seems like an unnecessary duplication to ask the client to pay for a BECx agent and a Passive House verifier. Or am I missing something? I can't find any LEED... Read more

Hello All! 

We are using TallyCat to extract quantities from our REVIT Model, and bring them over to EC3 to get a model GWP (focusing on material categories required to evaluate ILFI Zero Carbon certification).  There are a number of questions that are popping up!!

I am sure there are others trying the same thing, yes... maybe?! ... Read more

Welcome to the quiz portion of The Value of Variability.

Learning Objectives
Upon completing this course, participants will be able to:


1.  Understand why variability is important to the comfort and well-being of building occupants.

2.  Define “alliesthesia” and explain how it relates to the well-being of occupants... Read more