Are you a design or building professional who wants to learn more about sustainability—such as how to do energy modeling, improve the building envelope, or use renewables on a project? Now more than ever, it's time to join the sustainable... Read more

Hi Advising Leaders!

Lets get this forum going by introducing ourselves (yes, I know we mostly know each other, but just to be sure). And sharing what's most exciting and/or bugging us these days. Oh, and if you haven't already, please fill out your BG.com profile with a picture and bio. 

I'll start. I'm Nadav, president at... Read more

Hi All,

Has anyone dug into ASHRAE 2016 as part of the new v4.1 requirements or as codes start to adopt it? I recently presented on this and thought I should check my math to make sure I'm understanding and communicating this correctly.

My understanding is that there is a new reference baseline, that is essentially the ASHRAE 2004... Read more

I was wondering if any of you have experience with integrated PVs and/or solar glass. If so, can you could recommend manufactures for each? We are working on a multistory freestanding building in an urban site for a mid-Atlantic city. Because our site and roof area are limited we are looking to maximized the areas where we can generate power.... Read more

Hi all,

We have a newly constructed, core/shell project having some hot water issues in the core restrooms.

There is a 0.35 Toto lav installed throughout. The hot water heaters are adjacent on each floor, located in the janitor closets. We did the math, and there could be a gallon of water standing and cooling in the pipe between... Read more

We have an MEP engineer that is calculating peak loads at about 6 times passive house levels on a large commercial building that is at or near passive house levels of insulation and air infiltration. We suspect one reason is that he is figuring a 50% efficiency level for the ERV. We are showing him ERV systems with 80-90% efficiency, but they... Read more

Caseworks can be made from unsustainable wood and other materials, and with adhesives and finishes that offgas formaldehyde and other hazardous compounds.

BuildingGreen-Approved Casework

Approved caseworks are:

I know that there is a risk of starting a whole flurry of congrats through the forum, but this is a biggie, and deserves some recognition:

Congratulations Andrea and Melanie!! Huzzah!!

And a reminder--If you want to reach out to them privately, rather than through the forum, with your message, you can see anyone's email address by... Read more

Hello,

We’re looking for Design Energy Code Equivalents for Chinese commercial energy codes. Do any of you have  any good sources? I’ve only found data comparing ASHRAE 90.1 2013 to the Chinese Code at that time. We understand the Chinese code require a 65-75% energy savings over the baseline but don’t have good information for defining... Read more

Following up on one of our conversations on the vision vacuum and sustainability beyond certifications, I would like to help facilitate an offline conversation with anyone working within their firm to use the AIA COTE measures as a guiding framework in their firms/projects. Attached are my slides on my first pass at thinking about this at Page... Read more

Hi Everyone, 

Has anyone had success in finding organizations or programs that will recycle the hard hats? We are looking into options for recycling our expired hard hats that can no longer be used. Ideally, we would want to use a company with facilities across the country but we are open to any suggestions or ideas you all may have.... Read more

Welcome to the quiz portion of Five Reasons to Be Optimistic About Solar Energy!

Learning Objectives
Upon completing this course, participants will be able to:


Describe three ways how PV decreases environmental impact while increasing sustainability and health measures for communities.

Discuss PV life-cycle... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

Hi all!

I've heard several people talk about developing tools for assessing/codifying a client's values for a project as part of an integrated design process (ie. a set of questions, survey, etc.). Would anyone be willing to share?

(Z, are you listening? I specifically recall you mentioning a tool like this...)

Thanks!... Read more

Hey Peer Network! Curious, if we can crowd-source a solution here for the pervious pavers at our Omaha office (climate zone 5A). Apparently over the years we've tried to add different kinds of fill here (gravel) but it keeps... disappearing. Any recommendations with either a replacement product or fill item?