Is LEED Online mind-numbingly slow today for anyone else? Or is it just me? I may give up and try again tomorrow. Frustrating as I was hoping to submit a final review today. :(

Hello all, 

Wondering if anyone has experience with lead limits in electrical cable and wiring? 

LEED for Healthcare allows a limit of 300 ppm of lead in electrical wire and cabling - my search for compliant products has been all dead ends. (MRc PBT Source Reduction - lead, cadmium, and copper)

Acceptable regulations for... Read more

Hi all,

Thanks again to those who presented at the AIA Show & Tell! Here are the slides for some of the fascinating presentations we saw. Please do not share the slides outside of the networks unless they are marked “PUBLIC.”

There may be more to come; if you presented but did not yet provide permission for your slides to be... Read more

I'm looking to compile an outdoor weather station for a local project, and we'd like to add local outdoor CO2 information to our data. I usually work with Onset HOBO products, but they don't offer an outdoor CO2 sensor. Their weather stations can take data from any CO2 sensor with an analog output - does anyone have any suggestions?

Looking for an example or case study for a building utilizing a radiant heating/cooling in climate zone 4a. General use type is office with some public assembly spaces, total of 85,000 sf.

As usual, everyone, especially mechanical engineer, is terrified by the thought of "condensation." So far, I read a DGWW case study, "Energy... Read more

Board insulation has good thermal performance ranging from about R-4 to R-8 and is used as an integral part of a building envelope’s continuous insulation system.

Because board insulation is used on the building exterior, it is not always subject to the same material health and emissions requirements as batt insulation used inside the... Read more

Hello Sustainable Construction Leaders,

It's come to our attention that although we shared the slides from last fall's all-network Show & Tell in Atlanta, we neglected to include the presentations from the SCL Summit itself. Since we believe in "better late than never," here they are!

As a reminder: we have permission from... Read more

Here is a fundamental question regarding measuring operational carbon emissions that I'm sure many of you can clarify for me:  Let's say you are considering design options and you want to know the relative contribution of GWP of adding an additional inch of continuous insulation to the building envelope.  The GWP from embodied carbon will... Read more

On LEEDuser we divide checklists into multiple project phases. Specifically:

How many of these phases are relevant for BIT best practices?

Note that we also... Read more

Welcome to the quiz portion of VOCs: Still Here, Still Making Us Sick!

Important: This quiz covers all related articles within this topic. Scroll to the bottom of the article page to find links to all the articles covered by this quiz.

Learning Objectives
Upon completing this course, participants will be able to:


1.... Read more

Hi All,

My team member is leaving Webcor, and unfortunately that means we have to fill her big shoes with someone new! I thought I'd reachout here and see if you know anyone of high caliber looking for a Sustainability Manager position? Someone with LEED PM experience preferred, and a bit more technical background with MEP/ZNE ideally... Read more

Hi all,

As you know, the Carbon Leadership Forum has been busy in recent years growing the tent of discipline-based commitments for reducing embodied carbon. SE 2050 and MEP 2040 provide the platform and commitment for structural and MEP respectively, and there is now interest brewing for an additional commitment in support of civil... Read more

Under a high carbon scenario, most of North America will be 2 degrees C hotter by 2050. Meantime, we're designing buildings that will still be around in 2050, to codes that don't yet factor in chronic risks associated with climate change. I want to explain these risks to my colleagues; I'm hoping some of our green gurus can help answer the... Read more

Hey there SDLs!

We're having a debate in our firm about whether we're at a tipping point to hire an in-house energy modeler - someone capable of doing an MEP-caliber energy model inside a design firm. I know some you have in-house energy modelers on staff and I'd love to hear your experiences:

- How did you know your firm was at a... Read more

Reminder: For anyone interested in continuing to participate in the Climate Smart Wood Working Group, please note that we have joined the other CSWG and will have our first meeting next Wednesday.  Visit the Working Group page for the meeting invite and agenda.

Hi MEP Leaders!

Here's a reminder that our monthly meeting is coming right up--today at 2:00 pm ET.

There is a lot to talk about: James has put together a starting point for our "how to make the best use of your engineer" guide. And Summit plans...

You can view the agenda here.

All members of the SMEPL network are... Read more