If anyone else has gotten confused going between parts-per-million and percentages (parts per hundred!) for material reporting here's a little infographic that might help. Feel free to use or improve! 

Thanks to SERA especially David, Kira and Clark for an inspirational conversation with Paul Hawken about his latest book. I know I needed a positive perspective! Then I found this great "Regeneration Anthem" song and had to share.

https://regeneration.org/news/210915-we-can-change-world-regeneration-an...

Happy Fall to all.

We apologize, but the heating fuel cost calculator is no longer on the BuildingGreen website.

Take a look at Efficiency Maine's heating fuel cost calculator instead.

Hi all,

We have a newly constructed, core/shell project having some hot water issues in the core restrooms.

There is a 0.35 Toto lav installed throughout. The hot water heaters are adjacent on each floor, located in the janitor closets. We did the math, and there could be a gallon of water standing and cooling in the pipe between... Read more

Hi there SD Leaders,

We're running an LCA on one of our projects that's about to start construction that has had serious embodied carbon goals and I got a result that really surprised me. I haven't been able to find any obvious/glaring issues with the work, but these results are strange enough that I'm not feeling confident. I'm hoping... Read more

Exterior doors often have poor insulation and seals that allow air through.

BuildingGreen-Approved Exterior Doors

BuildingGreen has different criteria for commercial and residential exterior doors.

Commercial swing (hinged) doors must be NFRC-rated, certified, and labeled for U-factor. They have a maximum air leakage of 0.... Read more

Hi everyone, on our SDL Regional Leaders call today we touched on how different offices are engaging with the Youth Climate Strike on Sept 20, and I offered to share a few resources that we've developed:  

1) Here is our public-facing official statement/endorsement: https://www.vmdo.com/architecture-blog/vmdo-youth-climate-strike/?fbclid... Read more

Hello - 

I am looking for the recording and the PDF/ slides that were shared 3/6 for the project process share-out/ 5 min presentations. It was super inspiring and I would like to refresh my memory of some of what was shared. Thank you!

–
Alison Nash 
AIA, LEED AP ID+C, CPHC, WELL AP
Associate | Sustainability... Read more

Hey all - sorry I won't be able to join our call today. I had a client request an emergency meeting today (boo) because corporate mandated that they eliminate fossil fuel use from all their buildings (yay!) by 2025 and they've got a project underway that needs to pivot quickly. 

Had I been able to join, I wanted to share this in case... Read more

Hello Gurus,

I have a client (bldg owner) who has asked me to recommend a list of firms who have the internalized resilient design in their practice.

They are *not* asking for resiliency consultants right now, but for firms that they might hire for "regular" capital projects, but since resiliency is high on their priorities, they... Read more

All,

I've probably spoken to a few of you over the phone, but I wanted to make sure all of you know that we are hosting a 4 part webinar series on our Tally LCA software, kicking off tomorrow 10/10. We just released the new of Tally version and ended up doing far more development work than initially anticipated, in no small part due to... Read more

Hello,

We’re looking for Design Energy Code Equivalents for Chinese commercial energy codes. Do any of you have  any good sources? I’ve only found data comparing ASHRAE 90.1 2013 to the Chinese Code at that time. We understand the Chinese code require a 65-75% energy savings over the baseline but don’t have good information for defining... Read more

Hi Carbon Working Group,

It’s been a while since our last online meeting on 3/31 –- admittedly, a bit too long -- so I wanted to share some updates.  You might have seen Candice Pearson’s 5/13 post about the structure of the Contractor’s Commitment and how it’s evolving into a set of guidelines available not only to our SCL Group but to... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

P. U. L. Antelo, M.A.

Has anyone completed an LCA for an engineering structures lab, particularly one that has a strong wall and strong floor?