Do any of you have experience with Design For Freedom yet? It came to my attention and I'm trying to investigate. I would love to hear feedback and experiences that you may have at this point. It seems like an opportune moment for this issue of forced labor (yikes! so much I don't know...) to come to the forefront, and I'm curious to hear how... Read more

Greetings!

Ayers Saint Gross is in search of a Sustainable Design Coordinator to join our team. This person is anticipated to sit in any one of our offices - Baltimore; Washington, DC; Tempe, Arizona; or Austin, Texas. Fit and skillset are more important than geography. The position is anticipated as full-time, but if the right candidate... Read more

My colleague, Kira Gould, from the AIA National COTE communications committee, has a great question I am reposting here...

AIA National COTE: In the early 00s, COTE supported an initiative through which we created a Guide to the Green RFP and collected sample RFP language. That now dated guide is no longer findable in our resources and... Read more

Hello SD Leaders!

Two weeks ago a group of us gathered for the Winter 2020 Sustainable Design Leaders Summit. Those of us from BuildingGreen that were on site, greatly appreciated everyone's time and energy. It's always a pleasure to work along side you all!

Here is the summit report!

Reminder: We are giving a priority look... Read more

Hello All,
Checking in on experience with Armstrong's Tectum E-N with NEOPOR Graphite polysytrene GPS rigid foam insulation core in roof panels for exposed structure?
BASF says that NEOPOR uses up to 30% less material than other rigid foam; it is greenguard gold cerified. 

Interesting that the NEOPOR increases in R-value as... Read more

Welcome to the quiz portion of Equity in Design and Construction: Seven Case Studies!

Learning Objectives
Upon completing this course, participants will be able to:


We are trying to figure out how we are going to meet the LEED Credit for Building Life Cycle Impact Reduction for the first time.

One approach we're trying out: We're taking the results of our Tally model and looking at potential reductions from low-carbon concrete. However, the problem I am encountering is that when I take some of our... Read more

Hello Everyone!

Please see attached are the Flip Chart Notes from last week's 2018 SDL Summer Summit.

Enjoy~

RoseAnn

Hi all, 

Thank you again to those of you who attended the Spring 2024 SCL Summit! We had an amazing day of learning from one another, including from our presenters.

The slides for the 5-minute presentations are below, as well as the BuildingGreen slides from the Summit. Please be aware that we have permission from all of the... Read more

Water and electrical metering and submetering equipment provide valuable diagnostic information and verification of building energy and water usage.

Measuring Water Use

The Alliance for Water Efficiency recommends metering all new connections, retrofitting meters onto existing unmetered connections, and submetering all new... Read more

Welcome to the quiz portion of Exterior Paints: Long-Term Protection and Environmental Tradeoffs.

Learning Objectives
Upon completing this course, participants will be able to:


1. List the primary differences between alkyd and latex paints and stains and between wood, concrete, and metal primers.
2. Explain... Read more

For those of you who are close to CLT and mass timber, has the jump in US wood price also impacted the pricing of CLT on your projects, or viability of CLT compared to the cost of steel or concrete frame buildings?  

If anyone has price data comparing CLT today to pre-Covid pricing or any metric that would describe the percentage change... Read more

Hi all,

We are in the process of pursuing the Integrative Process for Health Promotion pilot credit on a project. Has anyone been through the process? What did you learn? How did it change/inform your design? Would you do it again?

Thanks!

Michelle

Hey team,

I'll go look to see who's in the MEP group, but does anyone in this circle have a northern California design engineer for institutional work that they'd particularly recommend? A group of folks we're engaged with is apparently having difficulty identifying a California-based MEP that everyone universally likes for high-... Read more

If your HVAC designers are addicted to the crack that is Trace 700, and knowing that Trane is giving up on that product in the coming year, what loads program are you weaning* them onto?

Asking for a friend:  Have any of you had success in using the Revit plug-in for loads?

*When told that they should use IESVE for loads, our HVAC... Read more