Championing the
Changemakers

Hello Colleagues,

You all know our industry’s progress over the past decade related to the impact of materials. We have come a long way. Today we have over 110 firms that have signed onto the A&D Materials Pledge, pledging to a holistic approach to materials considering: Human Health, Climate Health, Ecosystem Health, Social Health... Read more

Hello Green Gurus,

On October 5th a number of Sustainable Design Leaders gathered for the Fall 2021 SDL Virtual Summit and the BuildingGreen team is happy to now share with you all the event report here!

This report can be shared publicly. If you think someone would like to see it, such as firm leadership or prospective Peer... Read more

Wood decking requires potentially hazardous preservatives and stains, and plastic waste is a significant environmental problem.

BuildingGreen-Approved Decking

Composite decking approved by BuildingGreen has at least 50% total recycled content. For plastic decking, post-consumer content has to be greater than 50%.

Health and... Read more

All, today is the day I had committed to sending out the DRAFT request to equipment manufacturers of what is needed for full electrification.  I apologize that I didn't have time or focus to get my thoughts together till now (I had intended to share this with Chris and others prior to sending to the full group, but just didn't get my thoughts... Read more

Hi Friends, 

I'm working on an SOP for construction waste management for LBC core and LBC materials petal projects and wanted to get your input on the comingled facility requirements. According to the guidelines, any waste that goes to a comingled facility must be a facility that has an average diversion rate of 80% or higher as a... Read more

We are cautiously rekindling the age-old debate: how are we balancing modeling software for design /visualization and performance analysis during early phase of design.  

We are heavy SketchUp users for early design, and most of our staff have access to COVE tool for early performance analysis. Problem is, I’d rather use Revit to COVE... Read more

Welcome to the quiz portion of What You Need to Know About Concrete and Green Building.

Learning Objectives
Upon completing this course, participants will be able to:


1. Recognize concrete's environmental footprint and how to reduce the quantity of concrete used in buildings.
2. List the advantages and... Read more

Hi - We have some projects within reasonable reach of ILFI's Zero Carbon Certification, which will require purchasing some off-site renewable energy. As a State Building Code Council member, I'm also eyeing the Zero Code which we will seriously consider in the next 12 months; this also requires a purchase of off-site renewable energy. 

I... Read more

Is your team working on a LEED v4 or WELL project? 

Finding products for these projects is daunting, and even when you find products you believe will meet the requirements, you have to know exactly... Read more

Hi Gang, 

We are looking to implement the contractor commitment and are running into COVID-19 protocol barriers when looking at the Jobsite Wellness category specific to the soap as well as the food storage/eating areas on site. Anyone else run into this issue? 

-Kena 

Was anyone else surprised to see ASHRAE 228-2023 using eGRID Subregions for both the Regional Electricity Source Energy Conversion Factor and Regional Electricity Greenhouse Gas Emission Factors? In the past I have used eGRID sub-regions but also State and local utility conversion factors depending on what energy or operational carbon story I... Read more

I am excited to share with you the final draft of the letter back to LP50 manufacturers.  The LP50 manufacturers sent their “Closing the Loop on Product Transparency” to design firms earlier this year.  For more background information, please check out Chris Hellstern's original August 20th post on this Green Gurus forum.  When we posted the... Read more

Hi all,

We're doing some tool-related soul searching at WRNS and some folks here have raised Cove.Tool as a potentially interesting addition to our library. I'm looking for any insight you all can provide. Cove has come up various times, but curious if there's been any change for the better/worse in the past few years.

Do you use... Read more

Hi - I'm wondering if you have recommendations for a web/mobile app for occupants to self-assess comfort at regular intervals. I've downloaded comfy, but it wants to actually DO something about thermal discomfort by alerting discomfort and connecting, I believe, to the BMS. We just want to collect information at this point. And since I'm a... Read more

I'm exploring the use of phase change material for a project. Specifically, looking at the BioPCM/ENRG Blanket product. I see on their website that ZGF used it at University of Washington. I'd love to hear any feedback from folks who have used it, and more specifically how your energy model and MEP engineer accounted for it. Thanks!! https://... Read more

In an effort to share expert knowledge on the topic of whole building LCA, we are continuing our expert guest webinar series, addressing the topic of steel on March 19th at 1PM EDT. Michael Gryniuk PE, with LeMessurier and SE 2050, will be joining us to share his strategies for reducing the embodied carbon of steel. This webinar is particularly... Read more