Championing the
Changemakers

A colleague just pointed out an article about M-Fire. Its a factory applied fire inhibitor for wood construction. It's GreenGuard Gold but I can't find any real information. Have any of you heard of this or have any idea what it actually is? https://www.bisnow.com/national/news/construction-development/this-new-tech-will-stop-fires-before-they... Read more

Hi Everyone, 

This is quite last minute (due tonight) but please see below for an opportunity to email comments to EPA supporting national building material reuse measurement/methodology. Submission is easy, just a short email supporting C&D/reuse and any other thoughts on what to include/exclude in material pathways for reuse beyond... Read more

Hi everyone! The CLF Boston | NE Hub and BSA are holding an embodied carbon summit and we'd LOVE to see people from this group there. 

The first version of this summit was held in 2019, and since then we've made huge strides. Through our advocacy work, state and city regulations are addressing embodied carbon in procurement and materials... Read more

Auto-quiz used for CEUs for attendees of the 2023 SCL Fall Summit.

Producing a ton of cement releases approximately a ton of CO2 into the atmosphere, but accessories like finishes and additives can also be major sources of VOCs, soil contamination, and human health risks.

BuildingGreen-Approved Concrete Accessories

BuildingGreen approves the following concrete accessories:

Hello all,

I need future weather files for a project. We are looking at three years, 2050, 2075, and 2095 using two climate change scenarios, low emissions, and high emissions. I have seen ARUP's Weathershift site that uses RCP 8.5 and RCP 4.5. Are we assuming that 2.6 is not achievable? I would have used this as a low emissions scenario... Read more

On LEEDuser we divide checklists into multiple project phases. Specifically:

How many of these phases are relevant for BIT best practices?

Note that we also... Read more

Here is a fundamental question regarding measuring operational carbon emissions that I'm sure many of you can clarify for me:  Let's say you are considering design options and you want to know the relative contribution of GWP of adding an additional inch of continuous insulation to the building envelope.  The GWP from embodied carbon will... Read more

Has anyone used a commercial heat pump water heater for a large protect?  I have found a few manufacturers for this technology, but want to make sure this is a viable and cost approach to electrical eliminate gas on a path to all electric.

Welcome to the quiz portion of How To Run a Great Workshop: 37 Tips and Ideas.

Learning Objectives
Upon completing this course, participants will be able to:


1. Explain how the right mindset contributes to a successful design workshop.
2. Schedule a design workshop, set its agenda, and balance the skills of its... Read more

Hi all,

Thanks again to those who presented at the AIA Show & Tell! Here are the slides for some of the fascinating presentations we saw. Please do not share the slides outside of the networks unless they are marked “PUBLIC.”

There may be more to come; if you presented but did not yet provide permission for your slides to be... Read more

Hello Sustainable Construction Leaders,

It's come to our attention that although we shared the slides from last fall's all-network Show & Tell in Atlanta, we neglected to include the presentations from the SCL Summit itself. Since we believe in "better late than never," here they are!

As a reminder: we have permission from... Read more

I'm working with a project team that is looking into bird control options to prevent nesting/roosting/pooping on the scrim that is designed to scrim their building's facade.  They are looking at electrified tape, repellents, laser systems, etc -- Options that don't dramatically impact the building design.  The products they're looking at claim... Read more

Is LEED Online mind-numbingly slow today for anyone else? Or is it just me? I may give up and try again tomorrow. Frustrating as I was hoping to submit a final review today. :(

We have a client who is asking us to design a roughly 10 ksf Wellness Center for PHIUS 2021 certification.  The program includes several high density assembly type spaces - roughly 300 person peak occupant load for the building.  The Criteria Calculator that the architect showed us puts the building peak cooling load at 4 BTUH/sf (3000 sf/ton... Read more

Looking for an example or case study for a building utilizing a radiant heating/cooling in climate zone 4a. General use type is office with some public assembly spaces, total of 85,000 sf.

As usual, everyone, especially mechanical engineer, is terrified by the thought of "condensation." So far, I read a DGWW case study, "Energy... Read more