All,

Can anyone suggest a product for the following situation.  We are looking to insulate existing aluminum eterior column covers that have a three inch air gap.  The issue is there is no way to remove the covers without destroying them.  we would like to cut small holes, pump in the insulation  and then cap the holes.  Can anyone... Read more

I know that there is a risk of starting a whole flurry of congrats through the forum, but this is a biggie, and deserves some recognition:

Congratulations Andrea and Melanie!! Huzzah!!

And a reminder--If you want to reach out to them privately, rather than through the forum, with your message, you can see anyone's email address by... Read more

Does anyone up here do or have familiarity with anyone who regularly does NEPA EIS? If you need a definition for the acronym, please see here: https://www.epa.gov/nepa/national-environmental-policy-act-review-process#EIS. I've been asked if I know anything about it, to which the answer is no, but I'd like to get smarter about it and I'm hoping... Read more

Welcome to the quiz portion of A Guide to Selecting Sustainable Textiles.

Learning Objectives

Upon completing this course, participants will be able to:


Jenny/Dan:

What types of content do anticipate having in the Documentation Toolkit tab? Here's an example of what we have on LEEDuser:

https://leeduser.buildinggreen.com/credit/EBOM-2009/SSc5#tab-docs (login required)

The layout is a little complicated on LEEDuser, since we had to work with a lot of legacy content, but... Read more

Good morning all,

I'm new to the forum and I am really happy to be here. For the last year or so, I have been working to advance high performance design at Flad, grappling with so many of the issues discussed in this forum. Especially in the context of recent times, it feels really wonderful to join a group of people dedicated to helping... Read more

Hi everyone,

As part of our monthly SDLS call yesterday, we looked through the 2020 SD Leaders Winter Summit Report. To help paint an even fuller picture of what was covered at that summit, here are slides from many of the 5-minute presentations.

As a note: we have permission from these presenters to share their slides within the... Read more

The BuildingGreen Guide to Thermal Insulation provides detailed guidance on insulation products and practices, including recommendations on what insulation to use and what to avoid. It's a treasure trove of information for architects and designers, builders, and anyone who is actively considering the impact of insulation on the quality of your... Read more

Have any of you relied on Green Badger for LEED documentation on projects?

I am familiar with the tool and know Tommy from my time in Atlanta, but have not used it on a construction project.

Have you found value? Thoughts?

Either way, they publish a pretty nifty "LEED v4 Construction Tool Kit" that may be useful for your... Read more

Hello all,

Does anyone know of any Rebate Program for either induction cooking equipment or kitchen electrification (new or existing)? Looking for any local or state or even federal programs (outside of California) that incentivize designing/building/retrofitting towards an all electric kitchen for any program type (institutional, single... Read more

Glazing connects occupants to the outdoors, but with so many opportunities for air leakage, poor insulation, and thermal bridging, glazing is the primary weak link in building energy performance.

BuildingGreen approves glazing that offers strong energy performance properties for a variety of... Read more

Help regarding below...

OSHA, see below link, suggests 6' social distancing for unvaccinated or at-risk workers.

https://www.osha.gov/coronavirus/safework#role-employers-workers

Is your office going to maintain 6' social distancing for your workers?   Is the reason above because there are unvaccinated or at-risk workers?... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

Hi SCL,

It's my first time posting in the SCL group, as a somewhat new member. I'm grateful for any input you can provide to me!

My company, Nibbi Brothers, is currently brainstorming how to roll out an EV incentive program to employees. We recently polled our staff to get a general idea of where they stood with EV in terms of... Read more

It’s Summer Summit season! One of the “good problem to have” challenges we’ve had at recent SDL Summits has been too many great five-minute presentations. It’s hard to find time for them all. This year, since we’ll be online anyway, we can get a jump on that by starting the five-minute presentations early. Plus, we can share them across all the... Read more

Tomorrow is my last day at FXCollaborative before I head back to school. It has been such a gift to engage with you all over the past 10 years. Please stay in touch - my contact information is ilanajudah@gmail.com. I am headed out to UBC next week to do a deep dive into resilience and adaptation in urban environments.

FXCollaborative... Read more