As BuildingGreen’s Content & Data Wrangler, Fran is a spreadsheet and content-management wiz who:

Fran also compiles data submissions... Read more

Evaporative coolers use far less electricity than conventional refrigerant-cycle air conditioners and they operate without the use of refrigerants, both features that make them attractive for green buildings. However, their suitability is limited to drier climates, and most products use significant quantities of water.

BuildingGreen... Read more

Thanks to SERA especially David, Kira and Clark for an inspirational conversation with Paul Hawken about his latest book. I know I needed a positive perspective! Then I found this great "Regeneration Anthem" song and had to share.

https://regeneration.org/news/210915-we-can-change-world-regeneration-an...

Happy Fall to all.

The live webinar occurred on April 12, 2023.

Live webinar attendance confirmation closed on May 5, 2023.

Questions or comments about your purchase? Please let us know via our company contact form.

Dear SDL: Thanks to all who have already given their support to the AIA Resolution on Urgent and Sustained Climate Action. We're into the final push of getting out the vote to pass the resolution next Wednesday, June 5th afternoon in Las Vegas. This requires 2/3s of the voting delegates to pass. So we're asking anyone who 1) is attending as a... Read more

Hi all,

We have a newly constructed, core/shell project having some hot water issues in the core restrooms.

There is a 0.35 Toto lav installed throughout. The hot water heaters are adjacent on each floor, located in the janitor closets. We did the math, and there could be a gallon of water standing and cooling in the pipe between... Read more

Hello,

We’re looking for Design Energy Code Equivalents for Chinese commercial energy codes. Do any of you have  any good sources? I’ve only found data comparing ASHRAE 90.1 2013 to the Chinese Code at that time. We understand the Chinese code require a 65-75% energy savings over the baseline but don’t have good information for defining... Read more

All,

I've probably spoken to a few of you over the phone, but I wanted to make sure all of you know that we are hosting a 4 part webinar series on our Tally LCA software, kicking off tomorrow 10/10. We just released the new of Tally version and ended up doing far more development work than initially anticipated, in no small part due to... Read more

Hi All,

Has anyone dug into ASHRAE 2016 as part of the new v4.1 requirements or as codes start to adopt it? I recently presented on this and thought I should check my math to make sure I'm understanding and communicating this correctly.

My understanding is that there is a new reference baseline, that is essentially the ASHRAE 2004... Read more

Hi Everyone, 

Has anyone had success in finding organizations or programs that will recycle the hard hats? We are looking into options for recycling our expired hard hats that can no longer be used. Ideally, we would want to use a company with facilities across the country but we are open to any suggestions or ideas you all may have.... Read more

Hi Carbon Working Group,

It’s been a while since our last online meeting on 3/31 –- admittedly, a bit too long -- so I wanted to share some updates.  You might have seen Candice Pearson’s 5/13 post about the structure of the Contractor’s Commitment and how it’s evolving into a set of guidelines available not only to our SCL Group but to... Read more

The current Stantec/BuildingGreen featured topic is Material Health. Read on to learn the essentials, and then dive deep to earn CEUS.

Also see the Resilient Design featured topic, and also a survey of topics trending in Stantec’s regions.... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

Welcome to the quiz portion of Choosing Insulation: High-Performance Wall Assemblies – Unit 3.

Learning Objectives
Upon completing this course, participants will be able to:


1. Describe key environmental and performance factors for insulation materials.
2. Recount bottom-line insulation material... Read more

Hi Everyone!  About ten days ago, Megan Zack posted a note announcing her new role as Chief Sustainability Officer at Wight & Company. (Yay!)  I'm so delighted that she will be stepping into this leadership role at Wight to shepard the firm in the next chapter of their journey in sustainability. 

I wanted to take a moment to say... Read more

Welcome to the quiz portion of Counting Carbon: Understanding Carbon Footprints of Buildings.

Learning Objectives
Upon completing this course, participants will be able to:


1. Differentiate carbon counting approaches based on regulation or monetization from approaches aiming just to reduce carbon emissions.
2... Read more

What thoughts do you have? What have others said that you feel we want to capture?

The Vision Vacuum: What’s driving environmental and social progress in architecture today? What should be driving it, and where should we be going?

Medium-density fiberboard (MDF), particleboard, and interior-grade plywood can emit formaldehyde, a known human carcinogen. Some materials  come from non-sustainable sources.

BuildingGreen-Approved Panels

Products meet California Air Resources Board (CARB) ultra-low emitting formaldehyde (ULEF) or no-added-... Read more