Hi All,

If you have 5 minutes, we would appreciate your input in the Google Spreadsheet (linked below).  If you only have 1 minute, feel free to reply to this forum post and list your the typical equipment vendors you spec on projects.  :)

We're asking each of you to enter your "Top 3" specified vendors for each of the products... Read more

Hello all,

I am reaching out to this community as SMMA has a job opening for a Sustainable Design Analyst (like many of you recently posting job openings on this forum).

Here is the job posting link: https://smma.applytojob.com/apply/mah0aDkOJ0/Sustainable-Design-Analyst

Please note that this position will support... Read more

Many on this list teach or have strong contacts with university programs, so I'm hoping to leverage our network in service of something that may be of general benefit.

EDR has a Research Fellowship program where we host young talent for 3 or 12 months addressing new theme each year. The Fellow(s) get "academic freedom" and have no... Read more

Hello friends,

Anyone who will be attending NESEA's BuildingEnergy Boston conference next week is invited to an informal Green Gurus meetup! Stop by the Built Environment Plus booth (#4 on the map) at 6pm Monday (during the second half of the trade show reception) to say hi to some fellow Sustainability Leaders. SDL member Keihly Moore... Read more

Hi Friends, 

I'm working on an SOP for construction waste management for LBC core and LBC materials petal projects and wanted to get your input on the comingled facility requirements. According to the guidelines, any waste that goes to a comingled facility must be a facility that has an average diversion rate of 80% or higher as a... Read more

We are cautiously rekindling the age-old debate: how are we balancing modeling software for design /visualization and performance analysis during early phase of design.  

We are heavy SketchUp users for early design, and most of our staff have access to COVE tool for early performance analysis. Problem is, I’d rather use Revit to COVE... Read more

CEUs are available for reading all the building-envelope product guides and primer. Click here to learn more and take the quiz.

Water and air that penetrate building assemblies can damage materials, cause energy loss, and lead to mold, mildew, or other problems. The products used to address these may contain materials that are... Read more

Does anyone have an idea when the AIA Materials Pledge Reporting Framework will be available? Or is there a draft of what it looks like? 

BWBR is on a push to refine our approach towards materials. As AIA Material's Pledge signatory, we were hoping to incorporate the reporting framework into our efforts. Trying to get a sense of the... Read more

Was anyone else surprised to see ASHRAE 228-2023 using eGRID Subregions for both the Regional Electricity Source Energy Conversion Factor and Regional Electricity Greenhouse Gas Emission Factors? In the past I have used eGRID sub-regions but also State and local utility conversion factors depending on what energy or operational carbon story I... Read more

Hi All,

I wanted to pass on a few cool things we have going on at Built Environment Plus (formerly USGBC MA)  I really am conscious of not spamming you often and reserve posts for some of our most exciting happenings.

August 5, Building Tech Forum/MaterialsCAN: Getting to Zero with Embodied Carbon. Featuring 13 5-minute... Read more

I'm exploring the use of phase change material for a project. Specifically, looking at the BioPCM/ENRG Blanket product. I see on their website that ZGF used it at University of Washington. I'd love to hear any feedback from folks who have used it, and more specifically how your energy model and MEP engineer accounted for it. Thanks!! https://... Read more

Welcome to the quiz portion of Wood: What’s Good?

Learning Objectives
Upon completing this course, participants will be able to:


Dear all,

On a major renovation where the wall R-value/U-value needs to be brought up to energy code, specifically a mass wall situation, does anyone have insights on how the situation is best dealt with? On the project in question for me, the continuous insulation might have to be added to the inside surface of the mass wall and there... Read more

We have a client thats going through a TI remodel in a building thats a LEED Core+Shell certified building. One of the questions we are trying to figure out is are there things we need to be doing to not imperil the building's certification. 

I think the answer is that the landlord had to write tenant guidelines at the time of... Read more

This just in from Liz York at CDC: There's a webinar on Friday 11/2 at 3-4 ET on Building Design and Pandemics. For those who signed the petition to WHO urging action on aerosol emissions and have been following the ups and downs of those advisories, this is an especially welcome chance to hear from experts and ask questions. 

Centers... Read more