Championing the
Changemakers

I’m working on a hospitality project with a large scale farm to table operation, and I am concern about land space and agricultural practices. I'm looking for someone that can advise us on how to establish good agricultural planning and practices. The project is in Utah.

Has anyone work with consultants or academic group focus on this?... Read more

Greenbuild bound colleagues-

I unfortunately cannot join for the summit Tuesday but should be flying in early enough to potentially join the group for dinner. Are there any plans brewing that I might join?!

Let me know? Thanks.

Katie Rothenberg

Vice President, Sustainability & Innovatio 

HITT Contracting... Read more

Hi Everyone, 

This is quite last minute (due tonight) but please see below for an opportunity to email comments to EPA supporting national building material reuse measurement/methodology. Submission is easy, just a short email supporting C&D/reuse and any other thoughts on what to include/exclude in material pathways for reuse beyond... Read more

For questions and/or to be added to the Summer Summit waiting list, please email Jerelyn Wilson directly.

2019 Summer SDL Summit
Islandwood, Bainbridge Island, WA
July 31st- August 2nd, 2019

As we begin to look into Scope 3 emissions reduction strategies, it's important to understand ways to reduce tranportation emissions to project sites. Is anyone aware of best practices or programs for contractor carpooling to jobsites? I know many of my colleagues travel to work together in one vehicle because of parking limitations, however,... Read more

Furnaces heat air that is then distributed through ducting and warm-air registers.

Approved by BuildingGreen

Products approved by BuildingGreen include the highest-efficiency, sealed-combustion furnaces and high-efficiency wood or multi-fuel furnaces. A multi-fuel furnace uses several sources of energy such as wood, wood-pellets,... Read more

We have all these resources out here in the ether but it’s so hard to pull them into one spot! I was asked, last minute to join a client call today to help convince both the client (affordable housing developer) and the mechanical engineers to "stick with" a commitment to 100% electric design that was publicly stated when the competition was... Read more

Who else missed Building Green’s annual April Fool’s issue?

Hi: Great to see so many of you at AIA COTE Top Ten last week.  I'm forwarding the message below for those of you who know Marsha Maytum and can contribute to this important effort. Deadline is next Friday June 23rd!Thanks.

Mary Ann

Hello, friends,

During A'23, Je’Nen and I discussed our desire to send Marsha photos we have... Read more

Hello all, 

Wondering if anyone has experience with lead limits in electrical cable and wiring? 

LEED for Healthcare allows a limit of 300 ppm of lead in electrical wire and cabling - my search for compliant products has been all dead ends. (MRc PBT Source Reduction - lead, cadmium, and copper)

Acceptable regulations for... Read more

Under a high carbon scenario, most of North America will be 2 degrees C hotter by 2050. Meantime, we're designing buildings that will still be around in 2050, to codes that don't yet factor in chronic risks associated with climate change. I want to explain these risks to my colleagues; I'm hoping some of our green gurus can help answer the... Read more

Welcome to the quiz portion of The Sound of Sustainability: Acoustics in High-Performance Design!

Learning Objectives
Upon completing this course, participants will be able to:


Describe how increased acoustic performance benefits indoor environmental quality (IEQ).

Recount the negative impacts of poor acoustic... Read more

Hello everyone,

So sorry that some of you couldn't get onto the call on Tuesday! There was a bit of a problem with our Zoom links. I think we've figured it out, so we should be all set next time.

Here are the notes from the call. If you have any questions about something on there, please feel free to post them here and we'll try... Read more

THIS WEBINAR PURCHASE AND REGISTRATION IS CLOSED.

Hi All,

Has anyone successfully adopted a Revit to ClimateStudio workflow with their new export tool? Right now we are using cove.tool because it works reasonably well with iterative Revit modeling, but are itching to try a more accurate and nuanced alternative.

Thanks for any and all experiences!
Misha

We have a client who is asking us to design a roughly 10 ksf Wellness Center for PHIUS 2021 certification.  The program includes several high density assembly type spaces - roughly 300 person peak occupant load for the building.  The Criteria Calculator that the architect showed us puts the building peak cooling load at 4 BTUH/sf (3000 sf/ton... Read more

Hey, all. Two questions:

-How do we communicate to you LEED User content that needs to be pulled through to BIT-user pages? Are you all going to assess each BP page for potential articles/topics that will be linked?

-Regarding the forums- is there a way to notify program staff when a forum has an unanswered question? Hoping to... Read more