Championing the
Changemakers

We have an MEP engineer that is calculating peak loads at about 6 times passive house levels on a large commercial building that is at or near passive house levels of insulation and air infiltration. We suspect one reason is that he is figuring a 50% efficiency level for the ERV. We are showing him ERV systems with 80-90% efficiency, but they... Read more

Hello,

We’re looking for Design Energy Code Equivalents for Chinese commercial energy codes. Do any of you have  any good sources? I’ve only found data comparing ASHRAE 90.1 2013 to the Chinese Code at that time. We understand the Chinese code require a 65-75% energy savings over the baseline but don’t have good information for defining... Read more

Dear SDL: Thanks to all who have already given their support to the AIA Resolution on Urgent and Sustained Climate Action. We're into the final push of getting out the vote to pass the resolution next Wednesday, June 5th afternoon in Las Vegas. This requires 2/3s of the voting delegates to pass. So we're asking anyone who 1) is attending as a... Read more

On a large sports project, we worked with the structural engineer to spec low carbon / high SCM concrete mixes. Much of the floor area will be sealed and polished concrete, and a concrete sub is pushing back on the SCMs saying they should not be above 20% (with a preference for 0%) for the polish to finish properly, per the manufacturer. Anyone... Read more

Join our free Coffee Talk with Alex Spilger to discuss the latest WELL AP v2 exam. Hear what's new in this latest version, what to look for, and what to remember.

Alex combed the WELL Building Standard reference materials and took the v2 exam in writing an extensive exam prep guide.  Hear about... Read more

Hey Peer Network! Curious, if we can crowd-source a solution here for the pervious pavers at our Omaha office (climate zone 5A). Apparently over the years we've tried to add different kinds of fill here (gravel) but it keeps... disappearing. Any recommendations with either a replacement product or fill item? 

If anyone else has gotten confused going between parts-per-million and percentages (parts per hundred!) for material reporting here's a little infographic that might help. Feel free to use or improve! 

Hello all,

This month's SCDL call was full of great discussion! We decided this month that we are feeling good about where we are for the Task Force Agreement on defining social sustainabiltiy in our work. The aim is to work with this agreement for a while and see if it holds up as a process framework. There was also interest to invite... Read more

Fluid-applied roofing materials can be added to an existing roof to extend its life and provide reflective characteristics.

BuildingGreen-Approved Roofing

Products listed by BuildingGreen have VOC levels below 50 g/l and reflective surfaces to reduce heat gain.

Energy Star requires initial reflectance of 0.65 for low slopes... Read more

Welcome to the quiz portion of Passive House on Campus: Eight Exemplary Projects​!

Learning Objectives
Upon completing this course, participants will be able to:


Explain the primary reasons that higher-education projects are pursuing Passive House certification, including its impact on the environment and occupant health... Read more

Dear all,

Greetings. I'm presenting virtually to an audience of architecture and engineering faculty in India on the topic 'Introduction to Climate Change and Adaptive Architecture.' What is expected of the presentation is a broad overview of how climate change affects the built environment, challenges faced and some coping mechanisms. I... Read more

All,

I recently met Sahil Tadwalkar who is a Stanford MS Candidate in Civil Engineering. He and his group are interviewing design and construction industry professionals to understand issues and challenges around specifying and using low carbon solutions on projects. Interesting stuff! I encourage you to contribute by setting up an... Read more

It is with the greatest pleasure that I announce to this esteemed group the recognition of our very own and much-loved leader Nadav Malin as an Honorary AIA member. AIA COTE had the honor to serve as Nadav's sponsor and we are pleased and delighted with this outcome (but not surprised of course.) For the record, "The AIA recognizes the notable... Read more

Has anyone here been involved (taken or taught sessions) in the Healthy Materials Lab Online Certificate program for Healthier Materials? 

https://healthymaterialslab.org/learning-hub/e-learning-online-certifica...

I'm thinking about having some of our staff take this course, especially those that don't have a background in... Read more

BuildingGreen Approved, like its predecessor, GreenSpec, is an independent product evaluation service for BuildingGreen members. We offer an unbiased look at products: BuildingGreen does not accept any manufacturer fees for our evaluations. Here’s a quick tour of the platform and how to use it.